Conveyor of bulk materials of ejector type TSM-63/100
Russia
Russia
Description
The VMZ®TSM-63/100 ejector conveyor is designed for collecting and transporting bulk materials such as quartz sand, electrocorundum, cooper slag, steel or cast iron shot, plastic granules, grain and other bulk materials with a particle diameter of up to 10 mm.
Device and principle of operation of the transporter
Air from the compressor is supplied to line A. Passing through the air nozzle, the air flow in the mixing chamber creates a vacuum. Due to the discharge in the mixing chamber, air and the collected material are sucked into line B. After the mixing chamber, the mixture of air and the transported material enters the Venturi nozzle, where it accelerates and is transferred to the injection line B. The pressure of the incoming air and the discharge created in the mixing chamber are controlled by a pressure gauge and a vacuum gauge.
The suction and discharge lines are equipped with Kamlok quick–release connections, the air supply line from the compressor is equipped with a quick-release cam connection.
To prepare the transporter for operation, it is only necessary to connect it to the compressor air line and attach the suction and discharge hoses and the transporter is ready for operation.
The suction sleeve with a special nozzle installed on it is placed by the operator in a pile of collected material, and the end of the discharge sleeve is placed in any container suitable for this material.
The work of the transporter:
- Turn on the air supply on the compressor.
- Open the ball valve.
- When the nozzle freely draws in air without the transported material, the pressure gauge should show at least 5.4 bar, and the vacuum gauge from 1.8 to 2.2 inHg.
- Place the suction sleeve with the nozzle in a pile with the transported material.
- If there is an intermittent flow of the transported material, release the locking screws of the nozzle ring and slowly lift the adjusting ring until a steady flow is obtained. Tighten the locking screws.
- If the transport speed is too low, the adjusting ring can be lowered.
- After the work is completed, wait for the hoses to empty, turn off the compressor, close the ball valve, and then disconnect the hoses.
Specifications:
- The length of the suction line is not more than, m. - 30
- The diameter of the suction sleeve, mm - 63
- The length of the discharge line is not more than, m - 10
- The diameter of the discharge sleeve, mm - 100
- Productivity, t/hour (depending on the volume and pressure of the supplied air and the transported material) - 4
Characteristics
General Specifications
Russia
Russia
Specifications
Additional characteristics
Terms of delivery
Who provides the delivery of goods?
On the Enex marketplace, you order the product directly from its supplier, and Enex employees organize the delivery in the way you choose.What are the delivery methods?
You can choose any convenient way for you to receive an order:-
Pickup from partner locations or from the manufacturer's warehouse
If the manufacturer or trading company has the possibility of pickup, you can pick up your goods yourself or use the services of any transport company. Pickup is free of charge. -
Delivery to the terminal by a transport company
Pick up the goods at the nearest terminal of the Business Lines shopping center or DHL in your city. The delivery time and cost depend on your region and the dimensions of the cargo - they will be known at the stage of ordering. -
Delivery to the door by courier of the transport company
Receive the goods at your address via a Business Lines courier or DHL. The delivery time and cost depend on the region and the dimensions of the cargo - they will be known at the stage of ordering.
How can I keep track of the shipped product?
After you have selected your preferred delivery method and placed an order, you will be able to monitor the change in its status by the number in your personal account, and track the immediate location of the product by the track assigned by the delivery service. You will also receive email notifications about changes in the status of your order. This way, you will always know where your product is located and respond promptly to changes.Payment methods
Payment by bank card online
You can pay for the goods with bank cards "Visa", "Master Card", "Mir", "JCB". Payment by bank card is made without commission.- your bank card number;
- expiration date of your bank card;
- CVV code for Visa / CVC code for Master Card: the last 3 digits on the signature strip on the back of the card;
- confirm the card transaction, for example, with a one-time password from an SMS.
Payment according to the invoice
On the checkout page, select the “Invoice payment” option, and after placing the order, the system will automatically generate and send you an invoice for payment to the specified email address.Payment with bonuses
The buyer can pay part of the order cost (up to 20%) with Enex bonuses. The procedure and conditions for calculating and debiting bonuses are specified in section 7 Rules of sale and delivery.The seller's indication on the marketplace
Various suppliers of tools and equipment trade on the Enex marketplace. These can be both manufacturers and trading companies. In this case, the Marketplace acts as an agent (Chapter 52 of the Civil Code of the Russian Federation). Enex itself can also act as a seller for some products. Learn more about ordering from different suppliers.Return of goods
Is it possible to return the purchased product?
If you are not satisfied with the product purchased on the Enex platform, you can return it or exchange it under the conditions specified below. Since buyers conclude direct purchase and sale transactions with manufacturers on the Enex platform, the return of goods is carried out directly to manufacturers.
Return of goods of proper quality
For individuals
The buyer-an individual has the right to refuse the ordered goods at any time before receiving it, as well as after receiving the goods - within 7 days, not counting the day of purchase. The return of the goods is possible if its presentation and consumer properties are preserved, as well as a document confirming the fact and conditions of purchase of the goods.
The buyer does not have the right to refuse a product of proper quality having individually defined properties if the specified product can be used exclusively by the buyer acquiring it.
In case of refusal of the goods of proper quality, the cost of services for the organization of delivery to the buyer is not refunded. Transportation costs for the return of goods of proper quality are borne by the buyer. The method of returning the goods is determined by the buyer.
For legal entities
The return (exchange) of goods of proper quality by the buyer, who is a legal entity (individual entrepreneur), is not allowed, unless otherwise provided by the agreement with the supplier.
Return of goods of inadequate quality
For individuals
The buyer, who is an individual, in cases provided for by law, may return the goods of inadequate quality during the warranty period for the goods and demand a refund of the amount of money paid for the goods. The goods of inadequate quality, in agreement with the buyer, can be replaced with a similar product of proper quality.
For legal entities
The buyer, who is a legal entity (individual entrepreneur), in the event of the transfer of Goods of inadequate quality to him, has the right to make claims provided for in Article 475 of the Civil Code of the Russian Federation.
Distribution of responsibility
In case of return/replacement of low-quality goods, the cost of delivery of the goods is paid by the supplier. The supplier reserves the right to accept the goods of inadequate quality from the buyer and, if necessary, to check the quality of the goods. If, as a result of the examination of the goods, it is established that its shortcomings arose due to circumstances for which the supplier is not responsible, the buyer is obliged to reimburse the supplier for the costs of conducting the examination, as well as the costs associated with its storage and transportation of the goods.
If any defect is found in the product, the manufacturer and (or) the marketplace has the right to require the buyer to provide a photo of the product, the claimed defect, packaging, labeling (nameplate) of the manufacturer.
If the buyer, who is a legal entity (individual entrepreneur), refuses the goods of inadequate quality, such buyer is obliged to return such goods to the supplier. The buyer - an individual can also return the goods to the address of the supplier or Marketplace.
Transportation costs for the return of low-quality goods are borne by the supplier or Marketplace.
The difference between the shades of the goods in the photo and the real goods is not a sign of poor quality.
For questions about the return or exchange of goods, please contact us by phone 8 800 707-56-00 or by email: info@enex.market .
