GF-021 RED-BROWN primer
Russia
Belarus
Description
Type:GF-021 primer is a suspension of pigments and fillers in alkyd varnish, with the addition of solvents, a siccative and stabilizing substances.
Scope of application:The GF-021 primer is designed for priming metal and wooden surfaces under coatings with various enamels.
Advantages:
- the coating has good adhesion to metal;
- the primer forms a salt-resistant coating resistant to the action of mineral oil;
- the primer coating is resistant to temperature changes from minus 45 ° C to plus 60 °C.
Surface preparation:Before applying the primer, the metal surface must be thoroughly cleaned of rust, scale and other contaminants (it is necessary to remove notches, burrs, welding splashes, round off sharp edges, corners, teeth and welding seams; the surface must be free of grease, marking paint and other substances, such as mineral impurities, water-soluble salts, affecting on the quality of surface preparation), cleaned with a sandpaper (it is allowed to use a sandpaper with a grain size of 4 or 5 according to GOST 6456), degreased with white spirit (GOST 3134) or nephras C2-80/120 (TU RB 100006485.148) and thoroughly dried. It is most carefully necessary to clean the surface in the area of welds up to 3 cm wide from the remnants of fluxes, alkaline slags and oxides formed during welding. To improve the protective properties of the surface, it is recommended to pre-clean by sandblasting or shot blasting to a degree of purification from oxides 1-2. Painting should be done no later than 4 hours after surface preparation. On welds, end edges and hard-to-reach places, primers are applied with a brush in the form of a "strip layer" before painting. Previously painted surfaces are cleaned of fragile layers of the old coating, the old coating is removed, the entire surface is cleaned with a sandpaper (it is allowed to use a sandpaper with a grain size of 4 or 5 according to GOST 6456), dedusted, degreased and dried. It is recommended to carry out a control staining of a small area of the surface. To avoid condensation of moisture, the temperature of the painted surface must be at least 3 °C above the dew point temperature.
The unpainted wooden surface must be cleaned of resinous substances, dried, cleaned to remove the lint with a sandpaper (it is allowed to use a sandpaper with a grain size of 4 or 5 according to GOST 6456) and dust-free. Before applying the coating layer of enamel, the primed surface must be sanded. It is necessary to remove various impurities from the previously painted surface, completely remove the peeling coating, sand and dust the surface.
Coating application:Before application, the primer must be thoroughly mixed, if necessary, diluted to a working viscosity with solvent, xylene, or a mixture of one of these solvents with white spirit in a ratio of 1:1 by weight, solvents PC-2, 649, 650. For painting products in the electropole, the primer is diluted with a RE-4B diluent. The primer is applied by methods of pneumatic and airless spraying, spraying in an electric field, jet pouring, dipping, brush. The drying time of a single–layer coating up to 3 degrees at a temperature of (20 ± 2) ° C is no more than 24 hours. The thickness of the dried single-layer coating is 15-20 microns, after sandblasting or shot blasting, the coating thickness should be increased taking into account the degree of surface roughness Ra.
The consumptionof the primer for a single-layer coating is 60-100 g/m2 without taking into account the preparation of the painted surface, the method of application, the qualifications of personnel and other factors.
Precautions:When carrying out painting works in closed rooms, as well as after their completion, careful ventilation is necessary. Rubber gloves are used to protect the skin of the hands.
Keeping:Store the primer in a hermetically sealed container, protecting it from moisture and direct sunlight, away from heating devices, out of reach of children. Keep away from fire.
Characteristics
General Specifications
Belarus
Russia
Dimensions of packaged product
Specifications
Terms of delivery
Who provides the delivery of goods?
On the Enex marketplace, you order the product directly from its supplier, and Enex employees organize the delivery in the way you choose.What are the delivery methods?
You can choose any convenient way for you to receive an order:-
Pickup from partner locations or from the manufacturer's warehouse
If the manufacturer or trading company has the possibility of pickup, you can pick up your goods yourself or use the services of any transport company. Pickup is free of charge. -
Delivery to the terminal by a transport company
Pick up the goods at the nearest terminal of the Business Lines shopping center or DHL in your city. The delivery time and cost depend on your region and the dimensions of the cargo - they will be known at the stage of ordering. -
Delivery to the door by courier of the transport company
Receive the goods at your address via a Business Lines courier or DHL. The delivery time and cost depend on the region and the dimensions of the cargo - they will be known at the stage of ordering.
How can I keep track of the shipped product?
After you have selected your preferred delivery method and placed an order, you will be able to monitor the change in its status by the number in your personal account, and track the immediate location of the product by the track assigned by the delivery service. You will also receive email notifications about changes in the status of your order. This way, you will always know where your product is located and respond promptly to changes.Payment methods
Payment by bank card online
You can pay for the goods with bank cards "Visa", "Master Card", "Mir", "JCB". Payment by bank card is made without commission.- your bank card number;
- expiration date of your bank card;
- CVV code for Visa / CVC code for Master Card: the last 3 digits on the signature strip on the back of the card;
- confirm the card transaction, for example, with a one-time password from an SMS.
Payment according to the invoice
On the checkout page, select the “Invoice payment” option, and after placing the order, the system will automatically generate and send you an invoice for payment to the specified email address.Payment with bonuses
The buyer can pay part of the order cost (up to 20%) with Enex bonuses. The procedure and conditions for calculating and debiting bonuses are specified in section 7 Rules of sale and delivery.The seller's indication on the marketplace
Various suppliers of tools and equipment trade on the Enex marketplace. These can be both manufacturers and trading companies. In this case, the Marketplace acts as an agent (Chapter 52 of the Civil Code of the Russian Federation). Enex itself can also act as a seller for some products. Learn more about ordering from different suppliers.Return of goods
Is it possible to return the purchased product?
If you are not satisfied with the product purchased on the Enex platform, you can return it or exchange it under the conditions specified below. Since buyers conclude direct purchase and sale transactions with manufacturers on the Enex platform, the return of goods is carried out directly to manufacturers.
Return of goods of proper quality
For individuals
The buyer-an individual has the right to refuse the ordered goods at any time before receiving it, as well as after receiving the goods - within 7 days, not counting the day of purchase. The return of the goods is possible if its presentation and consumer properties are preserved, as well as a document confirming the fact and conditions of purchase of the goods.
The buyer does not have the right to refuse a product of proper quality having individually defined properties if the specified product can be used exclusively by the buyer acquiring it.
In case of refusal of the goods of proper quality, the cost of services for the organization of delivery to the buyer is not refunded. Transportation costs for the return of goods of proper quality are borne by the buyer. The method of returning the goods is determined by the buyer.
For legal entities
The return (exchange) of goods of proper quality by the buyer, who is a legal entity (individual entrepreneur), is not allowed, unless otherwise provided by the agreement with the supplier.
Return of goods of inadequate quality
For individuals
The buyer, who is an individual, in cases provided for by law, may return the goods of inadequate quality during the warranty period for the goods and demand a refund of the amount of money paid for the goods. The goods of inadequate quality, in agreement with the buyer, can be replaced with a similar product of proper quality.
For legal entities
The buyer, who is a legal entity (individual entrepreneur), in the event of the transfer of Goods of inadequate quality to him, has the right to make claims provided for in Article 475 of the Civil Code of the Russian Federation.
Distribution of responsibility
In case of return/replacement of low-quality goods, the cost of delivery of the goods is paid by the supplier. The supplier reserves the right to accept the goods of inadequate quality from the buyer and, if necessary, to check the quality of the goods. If, as a result of the examination of the goods, it is established that its shortcomings arose due to circumstances for which the supplier is not responsible, the buyer is obliged to reimburse the supplier for the costs of conducting the examination, as well as the costs associated with its storage and transportation of the goods.
If any defect is found in the product, the manufacturer and (or) the marketplace has the right to require the buyer to provide a photo of the product, the claimed defect, packaging, labeling (nameplate) of the manufacturer.
If the buyer, who is a legal entity (individual entrepreneur), refuses the goods of inadequate quality, such buyer is obliged to return such goods to the supplier. The buyer - an individual can also return the goods to the address of the supplier or Marketplace.
Transportation costs for the return of low-quality goods are borne by the supplier or Marketplace.
The difference between the shades of the goods in the photo and the real goods is not a sign of poor quality.
For questions about the return or exchange of goods, please contact us by phone 8 800 707-56-00 or by email: info@enex.market .
